Applications
- General manufacturing
- General fabrication
- Structural steel fabrication
- Transportation
- Sheet metal fabrication
- Light-gauge tube and sheet
Miller Power Source Lookup
Miller Deltaweld 600 Power Source
Dedicated Deltaweld 600 support for 600 amp heavy industrial MIG, flux-cored, air carbon arc gouging, ArcConnect/14-pin power-source configuration, Intellx feeders, and XR Plus push-pull gun paths.
Power source
MIG (GMAW)Flux-cored (FCAW)Accu-Pulse with Intellx Pro / EliteVersa-Pulse, HD MIG, and RMD with Intellx EliteAir carbon arc gouging (CAC-A)
Spec Sheet Quick Specs
Input And Output
- 208/230/460 V or 575 V, 3-phase, 60 Hz
- 600 A at 100% duty cycle
- 30-750 A, 10-44 V output range
- 115 V auxiliary power standard
Important 208/230 V Note
- On 208 V and 230 V input power, the data sheet states Deltaweld 600 operates at the same output ratings as Deltaweld 500.
- Use 460 V or 575 V input when the full Deltaweld 600 output rating is required.
Deltaweld 600 Power Source Stock Numbers
The April 2026 data sheet lists the 600 as a configurable power source, not as a Deltaweld 600 MIGRunner package.
| Stock number | Input power | Configuration |
|---|---|---|
| 907941003 | 208/230/460 V | ArcConnect, meters, 14-pin receptacle, and Insight |
| 907942003 | 575 V | ArcConnect, meters, 14-pin receptacle, and Insight |
Feeder And Process Matching
| Feeder path | Best fit | Process notes |
|---|---|---|
| Intellx Basic | Standard MIG / flux-cored Deltaweld 600 bench feeder setups | Arc control with fewer parameter adjustments |
| Intellx Pro | EZ-Set, Accu-Pulse, memory buttons, and steel/stainless programs | Accu-Pulse is available with Intellx Pro and Elite feeders |
| Intellx Elite | Expanded weld programs, Profile Pulse, XR Plus push-pull guns, remote wire drive, and Swingarc paths | Versa-Pulse, high-deposition MIG, RMD, and XR Plus push-pull compatibility require the Elite path |
| 14-pin legacy feeder path | Older Miller wire feeder setups because both Deltaweld 600 stock numbers include 14-pin | Verify feeder limits, cable requirements, and process availability before ordering |
Configurable System Notes
- The Deltaweld 600 includes the required Insight board per the April 2026 data sheet.
- Build the system by pairing the power source with ArcConnect control/motor cables, work sense leads, Intellx bench feeders, ROI/remote wire drive, or Swingarc components as needed.
- XR Plus push-pull guns require Intellx Elite feeder, Intellx Elite ROI / remote wire drive, or Intellx Elite Swingarc path.
- Industrial cart, cart accessory kit, water cooler, coolant fitting, and coolant are listed separately in the ordering information.
XR Plus Push-Pull Paths
The data sheet limits XR Plus push-pull guns to Intellx Elite feeder, Intellx Elite ROI / remote wire drive, or Intellx Elite Swingarc paths.
| Gun family | Stock numbers | Notes |
|---|---|---|
| XR-Aluma-Pro Plus air-cooled | 301575 (15 ft), 301574 (25 ft), 301739 (35 ft) | 300 A at 100% duty cycle; aluminum wire path |
| XR-Aluma-Pro Plus water-cooled | 301576 (15 ft), 301577 (25 ft), 301740 (35 ft) | 400 A at 100% duty cycle; requires gun wire kit 230708 for 1/16 in wire |
| XR-Pistol Plus air-cooled | 300753 (15 ft), 300754 (25 ft) | 200 A at 100% duty cycle / 250 A at 60% duty cycle |
| XR-Pistol Plus water-cooled | 300757 (25 ft) | 400 A at 100% duty cycle; requires gun wire kit 230708 for 1/16 in wire |
Gouge Support
Air Carbon Arc
- Dedicated constant-current gouge mode
- 30-750 A gouge range
- 600 A at 44 VDC, 100% duty cycle
Compatibility Snapshot
- The April 2026 data sheet lists Deltaweld 600 power-source stock numbers and configurable feeder/system components, but does not list Deltaweld 600 MIGRunner packages.
- Both Deltaweld 600 stock numbers include ArcConnect, meters, 14-pin receptacle, and Insight.
- On 208 V and 230 V input power, Deltaweld 600 operates at the same output ratings as Deltaweld 500 per the data sheet note.
- Accu-Pulse requires Intellx Pro or Intellx Elite feeders; Versa-Pulse, high-deposition MIG, RMD, and XR Plus push-pull gun compatibility require Intellx Elite.
- Use the exact power-source, feeder, ROI, Swingarc, cable, cooler, and cart accessory stock numbers before ordering.
Machine Specs
| Model | Stock numbers | Output / speed range | Rated output | Input power | Weight |
|---|---|---|---|---|---|
| Deltaweld 600 | 907941003, 907942003 | 30-750 A / 10-44 V | MIG: 600 A at 44 VDC, 100%; 700 A at 44 VDC, 60%; 750 A at 44 VDC, 40%. Gouge: 600 A at 44 VDC, 100% | 208/230/460 V or 575 V, 3-phase | 145 lb. (65.8 kg) |
Deltaweld 600 Configurable System Items
| Stock number | Catalog item | System role | Manufacturer UPC check | Notes |
|---|---|---|---|---|
| 907941003 | Deltaweld 600 208/230/460 V Power Source DELTAWELD 600 460V W/INSIGHT AND 14 PIN |
Power source only | 715959767477 | ArcConnect, meters, 14-pin receptacle, and Insight. Pair with feeder, gun, cables, and accessories. |
| 907942003 | Deltaweld 600 575 V Power Source DELTAWELD 600 575V W/INSIGHT AND 14 PIN |
Power source only | 715959767484 | ArcConnect, meters, 14-pin receptacle, and Insight. Pair with feeder, gun, cables, and accessories. |
| 951783001 | Intellx Basic Bench-Style Wire Feeder PKG,INTELLX, Q4015 ,DR ROLL KIT |
Single-wire feeder with Bernard BTB Gun 400 A | 715959701457 | AccuLock consumables and .035/.045 in V-groove drive rolls. |
| 951815001 | Intellx Basic Bench-Style Wire Feeder PKG, INTELLX DUAL Q4015 DR ROLL KIT |
Dual-wire feeder with two Bernard BTB Gun 400 A guns | 715959701549 | AccuLock consumables and .035/.045 in V-groove drive rolls. |
| 951784001 | Intellx Pro Bench-Style Wire Feeder PKG,INTELLX PRO, Q4015 ,DR ROLL KIT |
Single-wire feeder with Bernard BTB Gun 400 A | 715959701464 | AccuLock consumables and .035/.045 in V-groove drive rolls. |
| 951816001 | Intellx Pro Bench-Style Wire Feeder PKG, INTELLX PRO DUAL Q4015 DR ROLL KIT |
Dual-wire feeder with two Bernard BTB Gun 400 A guns | 715959701556 | AccuLock consumables and .035/.045 in V-groove drive rolls. |
| 951941001 | Intellx Elite Bench-Style Wire Feeder PKG,INTELLX ELITE, Q4015, DR ROLL KIT |
Single-wire feeder with Bernard BTB Gun 400 A | 715959701693 | Required path for Versa-Pulse, HD MIG, RMD, Profile Pulse, and XR Plus push-pull compatibility. |
| 951942001 | Intellx Elite Bench-Style Wire Feeder PKG,INTELLX ELITE DUAL, Q4015, DR ROLL KIT |
Dual-wire feeder with two Bernard BTB Gun 400 A guns | 715959701709 | Required path for Versa-Pulse, HD MIG, RMD, Profile Pulse, and XR Plus push-pull compatibility. |
Compatible Feeders
Miller Intellx Series Bench Feeders
Primary ArcConnect feeder path for Deltaweld 600 configurable systems.
Open support pageMiller 20 Series Bench Feeders
Use only after verifying the 14-pin legacy feeder setup and process requirements.
Open support pageMiller 74 MPa Plus Bench Feeders
Use only after verifying the 14-pin legacy feeder setup; pulse MIG is not available on this legacy Deltaweld path.
Open support pageCompatible Guns / Torches
Bernard BTB Gun 400 A
Listed with Intellx bench-style feeder choices.
Open support pageXR-Aluma-Pro Plus
Compatible only through Intellx Elite feeder, ROI / remote wire drive, or Elite Swingarc paths.
Open support pageXR-Pistol Plus
Compatible only through Intellx Elite feeder, ROI / remote wire drive, or Elite Swingarc paths.
Open support pageAccessories To Check
| Part number | Accessory | Use | Manufacturer UPC check | Buy / support |
|---|---|---|---|---|
| 301758 | Industrial cart INDUSTRIAL RUNNING GEAR/CYLINDER RACK |
For Deltaweld 350/500/600; industrial cooler integrates into the bottom of the cart. | 715959717755 | Buy link unavailable. |
| 301838 | Feeder swivel kit KIT,INDUSTRIAL HANDLE/FEEDER SWIVEL |
Required to add handle, MIG gun holder, cable management, and gas cylinder support to top-mounted feeders. | 715959717779 | Buy link unavailable. |
| 301528 | Cart accessory kit DELTAWELD 350/500 CART ACCESSORY KIT |
Single-wire feeder kit for industrial cart with regulator, gas hose, 4/0 feeder weld cable, work cable, and 9 ft ArcConnect cable. | 715959669320 | Buy link unavailable. |
| 301579 | Dual-wire cart accessory add-on kit DELTAWELD 350/500 DUAL CART ACCESSORY KIT |
Order with 301528 for dual-wire feeder setups. | 715959679084 | Buy link unavailable. |
| 301759 | Industrial water cooler INDUSTRIAL WATER COOLER |
2.5 gallon 115 V cooler for water-cooled torches; slides into the bottom of the industrial cart. | 715959717762 | Buy link unavailable. |
| 301529 | Stationary handle kit DELTAWELD 350 STATIONARY HANDLE KIT |
Allows easier movement and portability; not compatible with feeder swivel kit. | 715959669955 | Buy link unavailable. |
| 280471009 | ArcConnect control/motor cable, 9 ft ARCCONNECT CONTROL CABLE 9FT |
Connects Deltaweld 600 power source directly to feeder or remote operator interface. | 715959668712 | Buy link unavailable. |
| 280471015 | ArcConnect control/motor cable, 15 ft ARCCONNECT CONTROL CABLE 15FT |
Connects Deltaweld 600 power source directly to feeder or remote operator interface. | 715959668750 | Buy link unavailable. |
| 280471025 | ArcConnect control/motor cable, 25 ft ARCCONNECT CONTROL CABLE 25FT |
Connects Deltaweld 600 power source directly to feeder or remote operator interface. | 715959668743 | Buy link unavailable. |
| 300461 | Work sense lead, 25 ft WORK SENSE LEAD, PIPEWORX, 25 FT |
Provides accurate voltage feedback when connected from feeder to workpiece. | 715959392709 | Buy link unavailable. |
| 300462 | Work sense lead, 50 ft WORK SENSE LEAD, PIPEWORX, 50 FT |
Provides accurate voltage feedback when connected from feeder to workpiece. | 715959392716 | Buy link unavailable. |
| 081543 | Coolant fitting FTG,COOLANT |
5/8-18 UNF-2B left-hand thread fitting for coolant system setup. | 715959084956 | Buy link unavailable. |
| 043809 | Miller coolant COOLANT,ALUMINUM PROTECTING SOLD IN MULTI OF 4 |
Coolant for compatible Miller water-cooled systems. | 715959279512 | Buy link unavailable. |
Related Lookup Pages
Miller Deltaweld 500 Power Source
Dedicated Deltaweld 500 support for heavy industrial MIG, flux-cored, air carbon arc gouging, Intellx MIGRunner packages, ArcConnect feeder paths, and XR Plus push-pull aluminum gun options.
Open support pageMiller Deltaweld 350 Power Source
Dedicated Deltaweld 350 support for heavy industrial MIG, flux-cored, Intellx MIGRunner packages, ArcConnect feeder paths, and XR Plus push-pull aluminum gun options.
Open support pageMiller Deltaweld Power Sources
Deltaweld 350 and 500 support for heavy industrial MIG, flux-cored, Intellx feeder packages, and compatible bench feeder paths.
Open support pagei er wire feeder suppor
Related Miller wire feeder support path.
Open support pageMiller Intellx Series Bench Feeders
Intellx Basic, Pro, Elite, and Swingarc feeder path for Deltaweld 350/500 and XMT 400 shop systems.
Open support pageMiller 20 Series Bench Feeders
20 Series Basic and Digital bench feeder path for heavy industrial MIG and flux-cored work with CV/DC power sources.
Open support pageMiller 74 MPa Plus Bench Feeders
S-74 MPa Plus and D-74 MPa Plus feeder path for heavy industrial MIG, flux-cored, pulsed MIG, and aluminum push-pull systems.
Open support pageMiller MIG Drive Rolls
Drive roll lookup for Miller MIG and feeder setups.
Open support pageNeed More Help?
Wire Feed Problems
Use troubleshooting only after confirming the feeder model, power-source path, gun, wire size, and drive rolls.
Find My Part
Search by feeder stock number, gun family, drive roll, or power-source model when the setup is not clear.
Source: Miller Electric 2026 Full-Line Catalog, catalog pages 10, 16, 17, 18, 19, 122. Additional source: Miller Deltaweld 500/600 Systems MIG Welding System data sheet, issued April 2026, Index No. DC/16.8. Manufacturer UPC checks come from the uploaded Miller product/UPC file and are shown for verification only. Purchase placeholders are shown where no support page exists.